Menu
Your Cart

SHARP TMV 10" X 54" VARIABLE SPEED VERTICAL MILLING MACHINE

SHIPPING & DELIVERY
Call us now
Ask a question
SHARP TMV 10" X 54" VARIABLE SPEED VERTICAL MILLING MACHINE
SHARP TMV 10" X 54" VARIABLE SPEED VERTICAL MILLING MACHINE
Based on 0 reviews. - Write a review
$17,500.00
  • Stock: In Stock
  • Model: TMV
  • Weight: 3,000.00lb
  • Dimensions:
  • 75.00in x 70.00in x 91.78in
  • SKU: TMV
SHARP SHARP
Add to Cart
Buy Now Question
Add to Wish List Compare this Product
  • ISO 9002 certified quality to industry standards
  • Highest grade Meehanite® casting
  • A pair of precision ABEC-7 angular contact bearings to support spindle
  • High out-put double fans keep head and motor cool, to run jobs for extended periods without damaging the motor, belts and bearings
  • The spindle is ground and chromed to fit the housing to insure runout of .0002" T.I.R.
  • Motor shaft and variable speed drive pulleys are dynamically balanced, then chromed for flawless fit, ground ribs on inside diameter, for smooth speed changes
  • Motor shaft has an oil channel in the center that is fed by grease fitting on the lower end, to keep variable speed drive pulley moving smoothing on the shaft
  • Use a roller bearing for lower support of the shaft to ensure proper loading, support and alignment to prevent the shaft from being distorted by the tension of the belt, for quiet, accurate operation at any speed
  • Knuckle joint using bolts and circular T-slot design, allowing head to swivel left and right, up and down for better accuracy and performance
  • Table and saddle backlash is controlled by double nut design, keeps leadscrew in contact with bronze nuts all times to keep backlash at .0008" within 20"
  • Table and saddle are mounted with thrust bearings that preloaded the feed screw, eliminating end-play for precisely controlled lateral movement
  • Hardened and ground box ways on column and saddle for maximum rigidity
  • Hand scraped saddle and knee for better oil retention to avoid chips and dirt embed in the knee and damage the sliding surface
  • All wear areas are oil grooved for maximum lubrication
  • One shot lubrication system for lubrication of all ways and leadcrews
  • Internal coolant tank built into casting base for use with coolant system, coolant pump not included
  • Shown model TMV-DVS with Digital Variable Speed (DVS) head drive
Table Size (W x L/In.) 10 x 54
Spindle Taper R8
Diameter of Quill (In.) 3-3/8
Number of Spindle Speeds Mechanical Variable Speed
Range of Spindle Speeds (RPM) 60 - 4,500
Quill Down Feed Rates (IPR) .0015 - .003 - .006
Spindle Travel (In.) 5
Head Movement (Right or Left | Front or Back) 90° | 45°
Maximum Distance Spindle Nose to Table (In.) 16.9
Minimum Distance Spindle Nose to Table (In.) 5.375
Maximum Distance Spindle Center to Column (In.) 28.3
Minimum Distance Spindle Center to Column (In.) 9.8
Maximum Table Longitudinal Travel (In.) 39
Maximum Table Cross Travel (In.) 16.3
Maximum Knee Travel (In.) 15.3
Maximum Ram Travel (In.) 18.5
Width of Saddle (In.) 26
Number of T-Slots 3
Size of T-Slots (W x D/In.) 5/8 x 3/4
Distance Between T-Slot Centers (In.) 2-1/2

Main Motor (HP)		 3,
220V or 440V/3 Phase/60 Hz.,
Prewired 220V
Floor Space Dimensions (W x D x H/In.) 70 x 75 x 91.78
Machine Weight (Lbs.) 3,000
Design and specifications are subject to change without notice.
  • One Shot Lubrication System
  • Draw Bar
  • Front and Rear Rubber Way Covers
  • Toolbox with Tools
  • 380V or 575V/3 Phase/60 Hz. Transformer
  • ACU-RITE 203S 2-Axis (X & Y-Axis) DRO Milling Machine Package with Installation
  • ACU-RITE 203S 3-Axis (X, Y & Quill Axis) DRO Milling Machine Package with Installation
  • ACU-RITE 203S 3-Axis (X, Y & Knee Axis) DRO Milling Machine Package with Installation
  • FAGOR 20I 2-Axis (X & Y-Axis) DRO Milling Machine Package with Installation
  • FAGOR 30I 3-Axis (X, Y & Quill Axis) DRO Milling Machine Package with Installation
  • FAGOR 30I 3-Axis (X, Y & Knee Axis) DRO Milling Machine Package with Installation
  • NEWALL DP700 2-Axis (X & Y-Axis) DRO Milling Machine Package with Installation
  • NEWALL DP700 3-Axis (X, Y & Quill Axis) DRO Milling Machine Package with Installation
  • NEWALL DP700 3-Axis (X, Y & Knee Axis) DRO Milling Machine Package with Installation
  • X-Axis Power Feed with Installation
  • Y-Axis Power Feed with Installation
  • Z-Axis Power Feed with Installation
  • MAXI TORQUE-RITE Air Operated Power Drawbar System with Installation
  • 6" Riser Block with Installation
  • Right Angle Milling Attachment with Arbor
  • Horizontal/Vertical Rotary Table
  • KURT 6" Milling Machine Vise with Swivel Base
  • LYNDEX R-8 Round Collet Set
  • Clamping Kit
  • Drill Chuck and Arbor
  • Halogen Work Light
  • Auto Lube Pump
  • Coolant Pump System with Pump and Chip Pan at Base
  • UL Components Upgrade with Electrical Box - Factory Installed
  • UL Compliance Certificate - State of California
  • CE Mark
This website uses cookies to ensure you get the best experience on our website. This use may include analytics, personalization and ads. Learn More